Why Learning Plumbing Basics is Essential for Installing a Bathtub

Request Appointment

Just how do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Setting up a bathtub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old bathtub is conveniently accessible, the task can move easily; if you have to open up a wall to remove the old bathtub and place the new bath tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will need a helper to move out the old tub as well as set in the new one. Make certain you have certified yourself for the work and fit attempting it. Instead of employing a contractor to take control of a halfway-completed project, it is much better to think about utilizing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This short article will certainly help you install a new bath tub in your washroom if you have actually currently bought a new tub as well as don't require to alter the arrangement of your previous supply of water pipes.
Your devices and product list ought to comprise the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, turn on the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is typically the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
    Before going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly need a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipes.
    If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
    Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Secure the faucet in place with the producer supplied backnut. Once the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Mounting the Bath tub


    Utilizing both wood boards under its feet, place the bath tub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
    The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub till the spirit level reviews level.
    To set up taps, fit all-time low of the outermost flexible tap port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
    Turn on the water supply and inspect all joints and also brand-new pipework for leakages and tighten them if essential. Fill up the bath tub and also examine the overflow electrical outlet as well as the normal outlet for leakages.
    Finally, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub should wait until the tub has actually been used a minimum of once as this will certainly settle it right into its final position.

    Preparing for the Setup


    To start with, the supporting framework provided with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
    Fit the versatile faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
    Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its last setting.

    Tiling Around the Bath tub


    In the area where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to break a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, bring about issues with dampness and also possible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to permit the activity experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into consideration this motion before sealing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant glue and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    I was shown that write-up about Tools You Need to Install a New Bathtub from a friend on our other domain. Sharing is good. Helping people is fun. We thank you for reading our article about How to Install a Bathtub Yourself.


    Plumbing excellence awaits.

    Leave a Reply

    Your email address will not be published. Required fields are marked *